Materials list for an 8x10 deck
For a deck 10 feet along the house and 8 feet out, with 5.5 inch boards, a 1/8 inch gap, joists 16 inches on center and 10 percent waste. Change any of it in the calculator above.
| Item | Quantity | Cost |
|---|---|---|
| Deck boards, 5.5 in wide | 20 boards, 10 ft long | $190 |
| Joists | 9 boards, 8 ft long | $153 |
| Ledger and rim board | 2 boards, 10 ft long | $43 |
| Beam boards | 2 boards, 10 ft long | $43 |
| Posts | 3 | $127 |
| Footings | 3 | Not priced |
| Joist hangers | 9 | $31 |
| Deck screws | About 357, in 1 box of 1,000 | $41 |
| Total | About $628 |
Prices are store prices checked in October 2026, with all framing priced as treated 2x10 at $2.13 a foot. Change any price in the calculator to match your quote.
Every piece is 10 feet or shorter: 10 foot deck boards, ledger, rim and beam boards, and 8 foot joists. Short stock is light enough for one person to carry and easy to get home, and a spare deck board or two can become stair treads.
What an 8x10 deck costs
About $628 in lumber and hardware, or $8 per square foot, before concrete, railing, stairs, flashing, stain and tax. HomeAdvisor puts labor at $15 to $35 per square foot, so a contractor-built 8x10 comes to about $1,828 to $3,428. Compare cedar and composite boards in the deck cost calculator.
What fits on an 8x10 deck
An 8x10 deck is a landing with room to sit: a step out from a back door, a spot for a bistro table or a pair of chairs, or a place to set a grill near the kitchen. At 80 square feet it is the smallest size on this list.
Counting room to pull out chairs and walk past, an 8x10 deck holds a small table for two (6 by 6 feet). Set up for lounging instead, it holds a sofa, two chairs and a low table (10 by 8 feet). A round table for four would need 10 by 10 feet, which this deck does not have. These are rough planning sizes, so measure your own furniture.
Eight feet out from the house is the tight direction. A dining set for four wants about 10 feet with the chairs pulled out, so it would crowd the railing here. A small table against the rail, or a sofa set facing the yard, uses the space better. Put the stairs on a short side so people coming up do not walk through the seating.
The next size up, 10x10, adds 20 square feet: room for a round table for four; 2x8 joists instead of 2x6s.
Framing an 8x10 deck
Joists run out from the house and span about 8 feet from the ledger to the beam: 9 of them at 16 inches on center, each 8 feet long. The table gives the smallest joist DCA 6 allows for that span.
| Species | 12 in on center | 16 in on center | 24 in on center |
|---|---|---|---|
| Southern Pine | 2x6 | 2x6 | 2x8 |
| Douglas fir-larch, hem-fir, spruce-pine-fir | 2x6 | 2x6 | 2x8 |
| Redwood, western cedar | 2x6 | 2x6 | 2x8 |
In Southern Pine at 16 inches, that is a 2x6. The ledger, and any joist or rim a railing post bolts to, must be at least 2x8.
With one beam, 3 posts no more than 8 feet apart put the beam span at 5 feet. At an 8 foot joist span, DCA 6 Table 3A allows a beam of two 2x6s in Southern Pine to span 5 ft 8 in, the smallest two-ply beam that reaches. The two 2x10s priced in the list are more beam than this span needs.
For an 8 foot joist span, DCA 6 Table 5 puts 1/2 inch lag screws every 23 inches into a solid lumber band joist, about 7 along this 10 foot ledger, or through-bolts every 36 inches, about 5. No lead anchors, and no ledger on brick or stone veneer.
Keep the posts, and any footing for the stairs, at least 5 feet from the house wall if you can. DCA 6 makes a footing closer than that bear as deep as the house footing, which next to a basement means a very deep hole.
Deck boards on an 8x10 deck
18 rows of boards run along the house, across the joists. Each row is a single 10 foot board, so there are no joints to line up over joists. Laid on a diagonal, 5/4 wood boards need joists 12 inches apart, not 16: 11 joists instead of 9.
Railing and stairs
More than 30 inches up, a railing is required: 26 feet on the three open sides, about 7 railing posts and 58 balusters 1.5 inches wide, less the stair opening. See the baluster and stair calculators.
Footings and concrete
DCA 6 Table 4, for 8 foot joists and 5 feet between posts: footings 18 inches round or 16 inches square, 7 inches thick, on soil that bears 1,500 psf, under Southern Pine 6x6 posts up to 14 feet tall. Poured as a pad with a 12 inch pier up to the ground in 36 inch holes, the 3 beam footings take about 17 bags of 80 lb mix with 10 percent extra. Your frost line may call for deeper holes; the concrete footing calculator redoes the count.
Permits and code limits
Under the model code, only a deck of 200 square feet or less, no more than 30 inches up, not attached to the house and not serving the main exit door skips the permit. This deck bolts to the house, so it needs a permit under the model code even though 80 square feet is under the size limit. Built freestanding, low and away from the main door, a deck this size could qualify. Local rules vary, so ask your building department.
DCA 6 only covers decks that stick out from the house no farther than they run along it. An 8x10 deck runs 10 feet along the house and 8 feet out, so it is inside the limit. Turned the other way, 10 feet out from the house, it would not be. It also leaves out decks with snow loads over 40 psf, and hot tubs: water 3 feet deep weighs about 187 pounds per square foot, against the 40 psf live load its tables assume.
Before you build an 8x10 deck
Stairs take a big bite out of a small deck. DCA 6 wants stairs at least 36 inches wide, so the opening uses nearly a third of the 10 foot side, or more than a third of an 8 foot end, and people need a clear spot at the top to step on and off. Decide where the stairs land before you place any furniture.
Other deck sizes
8x1010x1010x1212x1212x1412x1612x2014x1614x2016x1616x2020x20
Common questions
How many deck boards do I need for an 8x10 deck?
20 boards 10 feet long: 18 rows of 5.5 inch boards, plus 10 percent waste.
How many joists do I need for an 8x10 deck?
9 joists 8 feet long at 16 inches on center, counting the two end joists.
How many screws do I need for an 8x10 deck?
About 357, two wherever a board crosses a joist, plus 10 percent.
How much does an 8x10 deck cost in materials?
About $628 in pressure-treated lumber and hardware, or $1,828 to $3,428 built by a contractor.
Can an 8x10 deck use 2x6 joists?
For the span, yes. DCA 6 allows a Southern Pine 2x6 at 16 inches on center to span 9 ft 0 in, more than the 8 foot depth. The ledger, and any joist or rim board that a railing post bolts to, must still be 2x8 or larger.
Is an 8x10 deck big enough for a table?
For a small table for two, yes. A round table for four needs about 10 by 10 feet once the chairs are pulled out, so on an 8 foot deep deck it would crowd the railing.
Tools for this job
Each link opens an Amazon search for that item. As an Amazon Associate I earn from qualifying purchases.
- Chalk line. Snaps a straight line for the first board and for trimming the board ends.
- Speed square. Marks square cuts on deck boards and joists.
- Deck board spacers. Keep the same gap between every board.
- Deck board straightening tool. Pulls a bowed board tight while you screw it down.
- Joist tape. Covers the tops of the joists so water does not sit on the wood.
- Driver bits. Spares for the drill, because deck screws wear bits out fast.
Sources
- International Residential Code 2021, Chapter 5: decks (R507)
- American Wood Council, DCA 6: Prescriptive Residential Wood Deck Construction Guide
- International Residential Code 2021, Chapter 3: landings and stairs (R311.3, R311.7) and guards (R312)
- International Residential Code 2021, Chapter 1: work exempt from permit (R105.2)
- McCoy's Building Supply: deck board prices, treated pine and composite
- McCoy's Building Supply: pressure-treated lumber and post prices
- McCoy's Building Supply: Simpson Strong-Tie LUS210Z joist hanger
- McCoy's Building Supply: deck screws, #10 x 2-1/2 in, box of 1,000
- HomeAdvisor: cost to build a deck, with labor rates
Facts on this page were last checked against these sources in October 2026.