Materials list for a 14x16 deck
For a deck 16 feet along the house and 14 feet out, with 5.5 inch boards, a 1/8 inch gap, joists 16 inches on center and 10 percent waste. Change any of it in the calculator above.
| Item | Quantity | Cost |
|---|---|---|
| Deck boards, 5.5 in wide | 33 boards, 16 ft long | $502 |
| Joists | 13 boards, 14 ft long | $388 |
| Ledger and rim board | 2 boards, 16 ft long | $68 |
| Beam boards | 2 boards, 16 ft long | $68 |
| Posts | 3 | $127 |
| Footings | 3 | Not priced |
| Joist hangers | 13 | $44 |
| Deck screws | About 858, in 1 box of 1,000 | $41 |
| Total | About $1,238 |
Prices are store prices checked in October 2026, with all framing priced as treated 2x10 at $2.13 a foot. Change any price in the calculator to match your quote.
Sixteen foot stock for the decking, ledger, rim and beam, and 14 foot joists. If you buy Douglas fir, hem-fir or spruce-pine-fir instead of Southern Pine, plan on 2x12 joists or 12 inch spacing, which changes the joist count and price in the list.
What a 14x16 deck costs
About $1,238 in lumber and hardware, or $6 per square foot, before concrete, railing, stairs, flashing, stain and tax. HomeAdvisor puts labor at $15 to $35 per square foot, so a contractor-built 14x16 comes to about $4,598 to $9,078. Compare cedar and composite boards in the deck cost calculator.
What fits on a 14x16 deck
A 14x16 deck adds two feet of depth to a 12x16, and that depth is what lets a table for eight fit, with a grill along the house beside it. It is also the deepest size here that a single span of Southern Pine 2x10s can cover.
Counting room to pull out chairs and walk past, a 14x16 deck holds a table for eight (14 by 10 feet) and a grill with room to cook (5 by 5 feet). Set up for lounging instead, it holds a sofa, two chairs and a low table (10 by 8 feet) and a grill with room to cook (5 by 5 feet). These are rough planning sizes, so measure your own furniture.
The table for eight fits with its long side running out from the house, 14 feet deep, and the grill takes a 5 foot strip beside it. For everyday use, a table for six, a grill and two lounge chairs fit together too.
The next size up, 12x20, adds 16 square feet: a beam of two 2x10s instead of a three-ply one.
Framing a 14x16 deck
Joists run out from the house and span about 14 feet from the ledger to the beam: 13 of them at 16 inches on center, each 14 feet long. The table gives the smallest joist DCA 6 allows for that span.
| Species | 12 in on center | 16 in on center | 24 in on center |
|---|---|---|---|
| Southern Pine | 2x10 | 2x10 | None |
| Douglas fir-larch, hem-fir, spruce-pine-fir | 2x10 | 2x12 | None |
| Redwood, western cedar | 2x10 | 2x12 | None |
In Southern Pine at 16 inches, that is a 2x10. The ledger, and any joist or rim a railing post bolts to, must be at least 2x8.
With one beam, 3 posts no more than 8 feet apart put the beam span at 8 feet. At a 14 foot joist span, DCA 6 Table 3A has no two-ply beam that reaches; the smallest that does is three 2x10s, allowed 8 ft 3 in. A fourth post cuts the span to 5 ft 4 in, where two 2x8s are enough. The list prices two 2x10s, which fall short at this span, so upgrade the beam or add the post.
For a 14 foot joist span, DCA 6 Table 5 puts 1/2 inch lag screws every 13 inches into a solid lumber band joist, about 16 along this 16 foot ledger, or through-bolts every 24 inches, about 9. No lead anchors, and no ledger on brick or stone veneer.
Joist span is measured from the face of the ledger to the face of the beam, so on a 14 foot deep deck the real span comes out a few inches under 14 feet once the ledger and beam are taken off. That gives Southern Pine 2x10s at 16 inches, which are allowed exactly 14 feet, a little room to spare.
Deck boards on a 14x16 deck
30 rows of boards run along the house, across the joists. Each row is a single 16 foot board, so there are no joints to line up over joists. Laid on a diagonal, 5/4 wood boards need joists 12 inches apart, not 16: 17 joists instead of 13.
Railing and stairs
More than 30 inches up, a railing is required: 44 feet on the three open sides, about 10 railing posts and 96 balusters 1.5 inches wide, less the stair opening. See the baluster and stair calculators.
Footings and concrete
DCA 6 Table 4, for 14 foot joists and 8 feet between posts: footings 24 inches round or 21 inches square, 10 inches thick, on soil that bears 1,500 psf, under Southern Pine 6x6 posts up to 14 feet tall. Poured as a pad with a 12 inch pier up to the ground in 36 inch holes, the 3 beam footings take about 24 bags of 80 lb mix with 10 percent extra. Your frost line may call for deeper holes; the concrete footing calculator redoes the count.
Permits and code limits
Under the model code, only a deck of 200 square feet or less, no more than 30 inches up, not attached to the house and not serving the main exit door skips the permit. This deck bolts to the house, and at 224 square feet it is over the size limit too, so even a freestanding version would need a permit. Local rules vary, so ask your building department.
DCA 6 only covers decks that stick out from the house no farther than they run along it. A 14x16 deck runs 16 feet along the house and 14 feet out, so it is inside the limit. Turned the other way, 16 feet out from the house, it would not be. It also leaves out decks with snow loads over 40 psf, and hot tubs: water 3 feet deep weighs about 187 pounds per square foot, against the 40 psf live load its tables assume.
Before you build a 14x16 deck
Do not let the beam drift outward when you set the posts, since the joists are already at their limit, and check the overhang table before you let the joists run past the beam.
Other deck sizes
8x1010x1010x1212x1212x1412x1612x2014x1614x2016x1616x2020x20
Common questions
How many deck boards do I need for a 14x16 deck?
33 boards 16 feet long: 30 rows of 5.5 inch boards, plus 10 percent waste.
How many joists do I need for a 14x16 deck?
13 joists 14 feet long at 16 inches on center, counting the two end joists.
How many screws do I need for a 14x16 deck?
About 858, two wherever a board crosses a joist, plus 10 percent.
How much does a 14x16 deck cost in materials?
About $1,238 in pressure-treated lumber and hardware, or $4,598 to $9,078 built by a contractor.
What size beam does a 14x16 deck need?
With three posts 8 feet apart, DCA 6 needs three Southern Pine 2x10s at a 14 foot joist span, which may span 8 ft 3 in. No two-ply beam reaches 8 feet there; two 2x12s stop at 7 ft 9 in. With four posts, about 5 ft 4 in apart, two 2x8s are enough.
Can 2x10 joists span 14 feet?
In Southern Pine at 16 inches on center, exactly: DCA 6 allows 14 ft 0 in. Douglas fir-larch, hem-fir and spruce-pine-fir 2x10s span 13 ft 7 in at 16 inches, so they need 12 inch spacing, where they reach 15 ft 8 in.
Tools for this job
Each link opens an Amazon search for that item. As an Amazon Associate I earn from qualifying purchases.
- Chalk line. Snaps a straight line for the first board and for trimming the board ends.
- Speed square. Marks square cuts on deck boards and joists.
- Deck board spacers. Keep the same gap between every board.
- Deck board straightening tool. Pulls a bowed board tight while you screw it down.
- Joist tape. Covers the tops of the joists so water does not sit on the wood.
- Driver bits. Spares for the drill, because deck screws wear bits out fast.
Sources
- International Residential Code 2021, Chapter 5: decks (R507)
- American Wood Council, DCA 6: Prescriptive Residential Wood Deck Construction Guide
- International Residential Code 2021, Chapter 3: landings and stairs (R311.3, R311.7) and guards (R312)
- International Residential Code 2021, Chapter 1: work exempt from permit (R105.2)
- McCoy's Building Supply: deck board prices, treated pine and composite
- McCoy's Building Supply: pressure-treated lumber and post prices
- McCoy's Building Supply: Simpson Strong-Tie LUS210Z joist hanger
- McCoy's Building Supply: deck screws, #10 x 2-1/2 in, box of 1,000
- HomeAdvisor: cost to build a deck, with labor rates
Facts on this page were last checked against these sources in October 2026.