Materials list for a 12x16 deck
For a deck 16 feet along the house and 12 feet out, with 5.5 inch boards, a 1/8 inch gap, joists 16 inches on center and 10 percent waste. Change any of it in the calculator above.
| Item | Quantity | Cost |
|---|---|---|
| Deck boards, 5.5 in wide | 29 boards, 16 ft long | $441 |
| Joists | 13 boards, 12 ft long | $332 |
| Ledger and rim board | 2 boards, 16 ft long | $68 |
| Beam boards | 2 boards, 16 ft long | $68 |
| Posts | 3 | $127 |
| Footings | 3 | Not priced |
| Joist hangers | 13 | $44 |
| Deck screws | About 744, in 1 box of 1,000 | $41 |
| Total | About $1,121 |
Prices are store prices checked in October 2026, with all framing priced as treated 2x10 at $2.13 a foot. Change any price in the calculator to match your quote.
Sixteen foot boards for the decking, ledger, rim and beam; 12s for the joists. The beam is the one place to buy up from the list: two 2x12s or three 2x10s for three posts, instead of the two 2x10s it prices.
What a 12x16 deck costs
About $1,121 in lumber and hardware, or $6 per square foot, before concrete, railing, stairs, flashing, stain and tax. HomeAdvisor puts labor at $15 to $35 per square foot, so a contractor-built 12x16 comes to about $4,001 to $7,841. Compare cedar and composite boards in the deck cost calculator.
What fits on a 12x16 deck
A 12x16 deck holds a table for six, a grill and two lounge chairs at once. At 192 square feet it is also the largest size on this list that stays under 200 square feet, the size limit in the model code permit exemption.
Counting room to pull out chairs and walk past, a 12x16 deck holds a table for six (12 by 9 feet), a grill with room to cook (5 by 5 feet) and two lounge chairs (7 by 7 feet). Set up for lounging instead, it holds a sofa, two chairs and a low table (10 by 8 feet) and a grill with room to cook (5 by 5 feet). These are rough planning sizes, so measure your own furniture.
One plan that fits: the six-seat table running out from the house at one end, and a 7 foot wide strip at the other end with the grill near the house and the lounge chairs beyond it. A round table for four and a grill fit side by side with a foot to spare.
The next size up, 14x16, adds 32 square feet: room for a table for eight; a size past the 200 square foot line in the permit exemption.
Framing a 12x16 deck
Joists run out from the house and span about 12 feet from the ledger to the beam: 13 of them at 16 inches on center, each 12 feet long. The table gives the smallest joist DCA 6 allows for that span.
| Species | 12 in on center | 16 in on center | 24 in on center |
|---|---|---|---|
| Southern Pine | 2x8 | 2x10 | 2x12 |
| Douglas fir-larch, hem-fir, spruce-pine-fir | 2x8 | 2x10 | 2x12 |
| Redwood, western cedar | 2x10 | 2x10 | 2x12 |
In Southern Pine at 16 inches, that is a 2x10. The ledger, and any joist or rim a railing post bolts to, must be at least 2x8.
With one beam, 3 posts no more than 8 feet apart put the beam span at 8 feet. At a 12 foot joist span, DCA 6 Table 3A allows a beam of two 2x12s in Southern Pine to span 8 ft 4 in, the smallest two-ply beam that reaches. A fourth post cuts the span to 5 ft 4 in, where two 2x8s are enough. The list prices two 2x10s, which fall short at this span, so upgrade the beam or add the post.
For a 12 foot joist span, DCA 6 Table 5 puts 1/2 inch lag screws every 15 inches into a solid lumber band joist, about 14 along this 16 foot ledger, or through-bolts every 29 inches, about 8. No lead anchors, and no ledger on brick or stone veneer.
If the house wall cannot take a ledger, DCA 6 has a non-ledger version: a second beam on posts runs along the house in place of the ledger, and any footing within 5 feet of the house wall has to bear as deep as the house footing.
Deck boards on a 12x16 deck
26 rows of boards run along the house, across the joists. Each row is a single 16 foot board, so there are no joints to line up over joists. Laid on a diagonal, 5/4 wood boards need joists 12 inches apart, not 16: 17 joists instead of 13.
Railing and stairs
More than 30 inches up, a railing is required: 40 feet on the three open sides, about 8 railing posts and 88 balusters 1.5 inches wide, less the stair opening. See the baluster and stair calculators.
Footings and concrete
DCA 6 Table 4, for 12 foot joists and 8 feet between posts: footings 24 inches round or 21 inches square, 10 inches thick, on soil that bears 1,500 psf, under Southern Pine 6x6 posts up to 14 feet tall. Poured as a pad with a 12 inch pier up to the ground in 36 inch holes, the 3 beam footings take about 24 bags of 80 lb mix with 10 percent extra. Your frost line may call for deeper holes; the concrete footing calculator redoes the count.
Permits and code limits
Under the model code, only a deck of 200 square feet or less, no more than 30 inches up, not attached to the house and not serving the main exit door skips the permit. This deck bolts to the house, so it needs a permit under the model code even though 192 square feet is under the size limit. Built freestanding, low and away from the main door, a deck this size could qualify. Local rules vary, so ask your building department.
DCA 6 only covers decks that stick out from the house no farther than they run along it. A 12x16 deck runs 16 feet along the house and 12 feet out, so it is inside the limit. Turned the other way, 16 feet out from the house, it would not be. It also leaves out decks with snow loads over 40 psf, and hot tubs: water 3 feet deep weighs about 187 pounds per square foot, against the 40 psf live load its tables assume.
Before you build a 12x16 deck
A 16 foot ledger often runs past a window, a dryer vent or a hose bib. DCA 6 does not let a ledger attach to brick or stone veneer, or under a cantilevered floor or bay window, so walk the wall with a tape before you settle where the deck goes.
Other deck sizes
8x1010x1010x1212x1212x1412x1612x2014x1614x2016x1616x2020x20
Common questions
How many deck boards do I need for a 12x16 deck?
29 boards 16 feet long: 26 rows of 5.5 inch boards, plus 10 percent waste.
How many joists do I need for a 12x16 deck?
13 joists 12 feet long at 16 inches on center, counting the two end joists.
How many screws do I need for a 12x16 deck?
About 744, two wherever a board crosses a joist, plus 10 percent.
How much does a 12x16 deck cost in materials?
About $1,121 in pressure-treated lumber and hardware, or $4,001 to $7,841 built by a contractor.
Does a 12x16 deck need a permit?
Almost always, because it bolts to the house. The model code only skips the permit for decks that are 200 square feet or less, no more than 30 inches above the ground, not attached to the house and not serving the main exit door. A freestanding, low 12x16 is under the size limit, but your local rules decide.
What size beam for a 12x16 deck?
With three posts 8 feet apart and 12 foot joists, DCA 6 needs a beam of two Southern Pine 2x12s or three 2x10s. With four posts, about 5 ft 4 in apart, two 2x8s are enough.
Tools for this job
Each link opens an Amazon search for that item. As an Amazon Associate I earn from qualifying purchases.
- Chalk line. Snaps a straight line for the first board and for trimming the board ends.
- Speed square. Marks square cuts on deck boards and joists.
- Deck board spacers. Keep the same gap between every board.
- Deck board straightening tool. Pulls a bowed board tight while you screw it down.
- Joist tape. Covers the tops of the joists so water does not sit on the wood.
- Driver bits. Spares for the drill, because deck screws wear bits out fast.
Sources
- International Residential Code 2021, Chapter 5: decks (R507)
- American Wood Council, DCA 6: Prescriptive Residential Wood Deck Construction Guide
- International Residential Code 2021, Chapter 3: landings and stairs (R311.3, R311.7) and guards (R312)
- International Residential Code 2021, Chapter 1: work exempt from permit (R105.2)
- McCoy's Building Supply: deck board prices, treated pine and composite
- McCoy's Building Supply: pressure-treated lumber and post prices
- McCoy's Building Supply: Simpson Strong-Tie LUS210Z joist hanger
- McCoy's Building Supply: deck screws, #10 x 2-1/2 in, box of 1,000
- HomeAdvisor: cost to build a deck, with labor rates
Facts on this page were last checked against these sources in October 2026.