Pitch & Plank

Roof pitch calculator

7/12 roof pitch

A 7/12 roof rises 7 inches for every 12 inches of level run. Enter your run to get the rafter length at this pitch.

Measurements

Run to the ridge

Half the building width on a simple gable roof

Results

Rafter length, no overhang
13' 10 11/16" (4.23 m)
Rise at the ridge
7' 0" (2.13 m)
Angle
30.26°
Slope
58.3%
Pitch multiplier
1.158
Roof type
Conventional
30.3°127

What a 7/12 pitch means

The roof goes up 7 inches for every 12 inches it runs level. That works out to an angle of 30.26 degrees, a slope of 58.3 percent, and a pitch multiplier of 1.158. It is 3.7 degrees steeper than a 6/12 roof.

A 7/12 roof is in the conventional range for houses. Over the same house, it has 15.8 percent more surface than a flat roof.

Where you see 7/12 roofs

7/12 is a common choice on two-story houses and newer homes, where a slightly steeper roof adds height to the front of the house without the cost of a very steep one.

Rafter lengths at 7/12

Ridge to the outside of the wall on a simple gable roof. The rafter length calculator adds the overhang and takes off the ridge board.

Building widthRafter lengthRise at ridgeRun
12 ft6' 11 3/8"3' 6"6 ft
16 ft9' 3 1/8"4' 8"8 ft
20 ft11' 6 15/16"5' 10"10 ft
24 ft13' 10 11/16"7' 0"12 ft
28 ft16' 2 1/2"8' 2"14 ft
32 ft18' 6 1/4"9' 4"16 ft
36 ft20' 10 1/16"10' 6"18 ft
40 ft23' 1 7/8"11' 8"20 ft

Roof area at 7/12

Multiply the flat area the roof covers, overhangs included, by 1.158. One roofing square is 100 square feet.

Area coveredRoof areaSquares
1,000 sq ft1,158 sq ft11.6
1,500 sq ft1,737 sq ft17.4
2,000 sq ft2,315 sq ft23.2
2,500 sq ft2,894 sq ft28.9
3,000 sq ft3,473 sq ft34.7

Roofing that works at 7/12

Lowest pitches from the International Residential Code. Local codes and maker instructions can be stricter.

RoofingLowest pitch allowedOn a 7/12 roof
Asphalt shingles2 in 12Yes
Clay or concrete tile2 1/2 in 12Yes
Wood shingles or shakes3 in 12Yes
Metal roof shingles3 in 12Yes
Slate4 in 12Yes
Roll roofing, mineral surfaced1 in 12Yes
Standing seam metal1/4 in 12Yes
Membrane or built-up roofing1/4 in 12Yes
Metal panels with lapped seams3 in 12Yes

Every roofing type in the table is allowed. 7/12 is the first whole-number pitch past the line where HomeAdvisor says labor costs go up, and the last one before the code adds its longer ice barrier rule at 8/12.

Underlayment and ice barrier at 7/12

At 7/12 one layer of underlayment is enough under shingles and tile.

Where the local code calls for an ice barrier along the eaves, it must reach at least 24 inches inside the outside wall. The extra 36 inch rule for steep roofs starts at 8/12.

Overhang past the wallIce barrier reaches, measured up the slope
None28 in
12 in42 in
24 in56 in

Attic space at 7/12

The code counts attic floor with at least 5 feet of headroom toward a room's size, and wants half of it to have 7 feet. Heights here run from the ceiling joists to a simple gable roof, before rafter and floor depth.

House widthRidge above the joistsWidth with 5 ft of headroomWidth with 7 ft of headroom
24 ft84' 0"6' 10 5/16"None
28 ft98' 0"10' 10 5/16"4' 0"
32 ft112' 0"14' 10 5/16"8' 0"
36 ft126' 0"18' 10 5/16"12' 0"
40 ft140' 0"22' 10 5/16"16' 0"

The ridge reaches 5 feet on a house about 17 feet wide, and 7 feet on one about 24 feet wide.

Working on a 7/12 roof

Past 6/12 the footing changes. On a 7/12 roof, crews usually set roof jacks with planks along the eave and work from them, tied off to an anchor at the ridge. That is a rule of thumb, and any roof is dangerous when wet or frosty.

OSHA counts anything over 4 in 12 as a steep roof, so workers 6 feet or more up need guardrails with toeboards, safety nets or personal fall arrest. The steepest stair the code allows in a house, 7 3/4 inch risers on 10 inch treads, climbs at 37.8 degrees. This roof is 7.5 degrees gentler.

More about 7/12 roofs

A 30 degree roof would be 6.93 in 12, so 7/12 is the whole-number pitch closest to 30 degrees. Moving up from 6/12 to 7/12 adds about 3.5 percent more roof surface over the same house, which shows up in the shingle and underlayment order. On a framing square, carpenters mark 7/12 cuts with the 12 inch mark on the body and the 7 inch mark on the tongue.

Nearby pitches

Compare with the 6/12 roof pitch and 8/12 roof pitch, or see every pitch in the chart on the roof pitch calculator. There is also a printable roof pitch chart that fits on one page.

Common questions

What is a 7/12 roof pitch in degrees?

30.26 degrees, which is a 58.3 percent slope.

What is the pitch multiplier for a 7/12 roof?

1.158. Multiply a level run or a flat area by it to get the sloped length or the roof area.

How long is a rafter on a 24 foot wide building at 7/12?

About 13' 10 11/16" from the ridge to the outside of the wall, before any overhang or ridge board deduction. The ridge sits 7' 0" above the top of the wall.

Can you put asphalt shingles on a 7/12 roof?

Yes. A 7/12 roof is above the 4 in 12 mark, so asphalt shingles go on with standard single underlayment.

Is a 7/12 roof walkable?

As a rule of thumb, footing gets poor at 7/12. Roof jacks or a harness are normal at this pitch. Any roof is dangerous when wet.

Is 7/12 the same as a 30 degree roof?

Very close. 7/12 is 30.26 degrees. An exact 30 degree roof would be 6.93 in 12, so 7/12 is the nearest whole-number pitch.

Does a 7/12 roof cost more to replace?

Usually a little. HomeAdvisor notes higher labor costs on roofs steeper than 6/12, and a 7/12 roof has about 16 percent more surface than the ground it covers.

Tools for this job

Each link opens an Amazon search for that item. As an Amazon Associate I earn from qualifying purchases.

Sources

Facts on this page were last checked against these sources in October 2026.

Related calculators