What a 10/12 pitch means
The roof goes up 10 inches for every 12 inches it runs level. That works out to an angle of 39.81 degrees, a slope of 83.3 percent, and a pitch multiplier of 1.302. It is 2.9 degrees steeper than a 9/12 roof.
A 10/12 roof is steep. It sheds water and snow fast and leaves more room in the attic, but it takes more material and more safety gear to build. Over the same house, it has 30.2 percent more surface than a flat roof.
Where you see 10/12 roofs
10/12 shows up on Victorian and Tudor-style houses, steep farmhouse gables, and cross gables meant to stand out from a lower main roof.
Rafter lengths at 10/12
Ridge to the outside of the wall on a simple gable roof. The rafter length calculator adds the overhang and takes off the ridge board.
| Building width | Rafter length | Rise at ridge | Run |
|---|---|---|---|
| 12 ft | 7' 9 3/4" | 5' 0" | 6 ft |
| 16 ft | 10' 4 15/16" | 6' 8" | 8 ft |
| 20 ft | 13' 0 3/16" | 8' 4" | 10 ft |
| 24 ft | 15' 7 7/16" | 10' 0" | 12 ft |
| 28 ft | 18' 2 11/16" | 11' 8" | 14 ft |
| 32 ft | 20' 9 15/16" | 13' 4" | 16 ft |
| 36 ft | 23' 5 3/16" | 15' 0" | 18 ft |
| 40 ft | 26' 0 7/16" | 16' 8" | 20 ft |
Roof area at 10/12
Multiply the flat area the roof covers, overhangs included, by 1.302. One roofing square is 100 square feet.
| Area covered | Roof area | Squares |
|---|---|---|
| 1,000 sq ft | 1,302 sq ft | 13.0 |
| 1,500 sq ft | 1,953 sq ft | 19.5 |
| 2,000 sq ft | 2,603 sq ft | 26.0 |
| 2,500 sq ft | 3,254 sq ft | 32.5 |
| 3,000 sq ft | 3,905 sq ft | 39.1 |
Roofing that works at 10/12
Lowest pitches from the International Residential Code. Local codes and maker instructions can be stricter.
| Roofing | Lowest pitch allowed | On a 10/12 roof |
|---|---|---|
| Asphalt shingles | 2 in 12 | Yes |
| Clay or concrete tile | 2 1/2 in 12 | Yes |
| Wood shingles or shakes | 3 in 12 | Yes |
| Metal roof shingles | 3 in 12 | Yes |
| Slate | 4 in 12 | Yes |
| Roll roofing, mineral surfaced | 1 in 12 | Yes |
| Standing seam metal | 1/4 in 12 | Yes |
| Membrane or built-up roofing | 1/4 in 12 | Yes |
| Metal panels with lapped seams | 3 in 12 | Yes |
Nothing in the roofing table is ruled out. At this pitch the roof is a large part of what you see from the street, which is one reason steep gables so often get slate, architectural shingles or standing seam metal. Shingles go on with the nailing in the maker's instructions, at least four nails per strip shingle; the code only sends you to the maker's steep slope instructions above 21 in 12.
Underlayment and ice barrier at 10/12
At 10/12 one layer of underlayment is enough under shingles and tile.
Where the local code calls for an ice barrier along the eaves, it must reach at least 24 inches inside the outside wall. At 10/12 it must also reach at least 36 inches up the slope from the eave, whichever is farther.
| Overhang past the wall | Ice barrier reaches, measured up the slope |
|---|---|
| None | 36 in |
| 12 in | 47 in |
| 24 in | 62 in |
Attic space at 10/12
The code counts attic floor with at least 5 feet of headroom toward a room's size, and wants half of it to have 7 feet. Heights here run from the ceiling joists to a simple gable roof, before rafter and floor depth.
| House width | Ridge above the joists | Width with 5 ft of headroom | Width with 7 ft of headroom |
|---|---|---|---|
| 24 ft | 120' 0" | 12' 0" | 7' 2 3/8" |
| 28 ft | 140' 0" | 16' 0" | 11' 2 3/8" |
| 32 ft | 160' 0" | 20' 0" | 15' 2 3/8" |
| 36 ft | 180' 0" | 24' 0" | 19' 2 3/8" |
| 40 ft | 200' 0" | 28' 0" | 23' 2 3/8" |
The ridge reaches 5 feet on a house about 12 feet wide, and 7 feet on one about 17 feet wide.
Working on a 10/12 roof
A 10/12 roof is too steep to stand on at all. Every move happens from planks on roof jacks, with a harness tied to an anchor, and materials are hoisted up rather than carried. That is a rule of thumb, and any roof is dangerous when wet or frosty.
OSHA counts anything over 4 in 12 as a steep roof, so workers 6 feet or more up need guardrails with toeboards, safety nets or personal fall arrest. The steepest stair the code allows in a house, 7 3/4 inch risers on 10 inch treads, climbs at 37.8 degrees. This roof is 2.0 degrees steeper than that.
More about 10/12 roofs
At this pitch the attic starts to become living space. Over a 28 foot wide house the ridge is about 11 ft 8 in above the ceiling joists before framing depth, enough for a strip of floor about 11 feet wide with 7 feet of headroom.
Nearby pitches
Compare with the 9/12 roof pitch and 11/12 roof pitch, or see every pitch in the chart on the roof pitch calculator. There is also a printable roof pitch chart that fits on one page.
Common questions
What is a 10/12 roof pitch in degrees?
39.81 degrees, which is a 83.3 percent slope.
What is the pitch multiplier for a 10/12 roof?
1.302. Multiply a level run or a flat area by it to get the sloped length or the roof area.
How long is a rafter on a 24 foot wide building at 10/12?
About 15' 7 7/16" from the ridge to the outside of the wall, before any overhang or ridge board deduction. The ridge sits 10' 0" above the top of the wall.
Can you put asphalt shingles on a 10/12 roof?
Yes. A 10/12 roof is above the 4 in 12 mark, so asphalt shingles go on with standard single underlayment.
Is a 10/12 roof walkable?
A 10/12 roof is too steep to walk on. Work at this pitch calls for roof jacks, staging and a harness. Any roof is dangerous when wet.
Can a 10/12 roof have a room in the attic?
Often. Over a 28 foot wide house a 10/12 roof puts the ridge about 11 ft 8 in above the ceiling joists, before framing depth, which leaves a strip about 11 feet wide with 7 feet of headroom. The attic table on this page shows other widths.
Is 10/12 steeper than a staircase?
Yes. The steepest stair the code allows in a house, 7 3/4 inch risers on 10 inch treads, climbs at 37.8 degrees. A 10/12 roof is 39.8 degrees.
Tools for this job
Each link opens an Amazon search for that item. As an Amazon Associate I earn from qualifying purchases.
- Speed square. Held against a rafter with a small level on top, it reads the pitch straight off its scale.
- Digital angle finder. Set it on a rafter or on the roof and it shows the angle in degrees.
- Level, 24 inch. Held level against a rafter, it lets you measure the rise at the 12 inch mark.
- Tape measure. Measures the rise, the run and the span.
Sources
- International Residential Code 2021, Chapter 9: roof drainage (R903) and roof coverings (R905)
- International Residential Code 2021, Chapter 3: room area and ceiling height (R304, R305) and stairs (R311.7)
- OSHA 29 CFR 1926.500: definitions of low-slope and steep roofs
- OSHA 29 CFR 1926.501: fall protection in construction
- HomeAdvisor: shingle roof replacement cost, with removal of the old roof
Facts on this page were last checked against these sources in October 2026.