Pitch & Plank

Roof pitch calculator

11/12 roof pitch

An 11/12 roof rises 11 inches for every 12 inches of level run. Enter your run to get the rafter length at this pitch.

Measurements

Run to the ridge

Half the building width on a simple gable roof

Results

Rafter length, no overhang
16' 3 3/8" (4.96 m)
Rise at the ridge
11' 0" (3.35 m)
Angle
42.51°
Slope
91.7%
Pitch multiplier
1.357
Roof type
Steep
42.5°1211

What an 11/12 pitch means

The roof goes up 11 inches for every 12 inches it runs level. That works out to an angle of 42.51 degrees, a slope of 91.7 percent, and a pitch multiplier of 1.357. It is 2.7 degrees steeper than a 10/12 roof.

An 11/12 roof is steep. It sheds water and snow fast and leaves more room in the attic, but it takes more material and more safety gear to build. Over the same house, it has 35.7 percent more surface than a flat roof.

Where you see 11/12 roofs

11/12 is less common as a main roof but appears on steep front gables, Tudor-style houses and dormers. At 42.5 degrees it looks nearly as steep as a 45 degree roof.

Rafter lengths at 11/12

Ridge to the outside of the wall on a simple gable roof. The rafter length calculator adds the overhang and takes off the ridge board.

Building widthRafter lengthRise at ridgeRun
12 ft8' 1 11/16"5' 6"6 ft
16 ft10' 10 1/4"7' 4"8 ft
20 ft13' 6 13/16"9' 2"10 ft
24 ft16' 3 3/8"11' 0"12 ft
28 ft18' 11 7/8"12' 10"14 ft
32 ft21' 8 7/16"14' 8"16 ft
36 ft24' 5"16' 6"18 ft
40 ft27' 1 9/16"18' 4"20 ft

Roof area at 11/12

Multiply the flat area the roof covers, overhangs included, by 1.357. One roofing square is 100 square feet.

Area coveredRoof areaSquares
1,000 sq ft1,357 sq ft13.6
1,500 sq ft2,035 sq ft20.3
2,000 sq ft2,713 sq ft27.1
2,500 sq ft3,391 sq ft33.9
3,000 sq ft4,070 sq ft40.7

Roofing that works at 11/12

Lowest pitches from the International Residential Code. Local codes and maker instructions can be stricter.

RoofingLowest pitch allowedOn an 11/12 roof
Asphalt shingles2 in 12Yes
Clay or concrete tile2 1/2 in 12Yes
Wood shingles or shakes3 in 12Yes
Metal roof shingles3 in 12Yes
Slate4 in 12Yes
Roll roofing, mineral surfaced1 in 12Yes
Standing seam metal1/4 in 12Yes
Membrane or built-up roofing1/4 in 12Yes
Metal panels with lapped seams3 in 12Yes

All of the roofing in the table may be used. Slate and tile weigh far more than shingles, so before switching a roof like this to either one, check that the rafters were sized for the weight. Shingles keep the maker's normal nailing, since the code's steep slope line for shingles is 21 in 12.

Underlayment and ice barrier at 11/12

At 11/12 one layer of underlayment is enough under shingles and tile.

Where the local code calls for an ice barrier along the eaves, it must reach at least 24 inches inside the outside wall. At 11/12 it must also reach at least 36 inches up the slope from the eave, whichever is farther.

Overhang past the wallIce barrier reaches, measured up the slope
None36 in
12 in49 in
24 in65 in

Attic space at 11/12

The code counts attic floor with at least 5 feet of headroom toward a room's size, and wants half of it to have 7 feet. Heights here run from the ceiling joists to a simple gable roof, before rafter and floor depth.

House widthRidge above the joistsWidth with 5 ft of headroomWidth with 7 ft of headroom
24 ft132' 0"13' 1 1/16"8' 8 3/4"
28 ft154' 0"17' 1 1/16"12' 8 3/4"
32 ft176' 0"21' 1 1/16"16' 8 3/4"
36 ft198' 0"25' 1 1/16"20' 8 3/4"
40 ft220' 0"29' 1 1/16"24' 8 3/4"

The ridge reaches 5 feet on a house about 11 feet wide, and 7 feet on one about 15 feet wide.

Working on an 11/12 roof

On an 11/12 roof workers move from plank to plank on roof jacks and roof ladders, always tied off. Shingle bundles cannot be set down on the roof at all; they wait on the planks. That is a rule of thumb, and any roof is dangerous when wet or frosty.

OSHA counts anything over 4 in 12 as a steep roof, so workers 6 feet or more up need guardrails with toeboards, safety nets or personal fall arrest. The steepest stair the code allows in a house, 7 3/4 inch risers on 10 inch treads, climbs at 37.8 degrees. This roof is 4.7 degrees steeper than that.

More about 11/12 roofs

An 11/12 roof has about 21 percent more surface than a 6/12 roof over the same house, and it is slow work. Both show up in the price, so expect a quote for a roof this steep to run higher per square than one for a lower roof.

Nearby pitches

Compare with the 10/12 roof pitch and 12/12 roof pitch, or see every pitch in the chart on the roof pitch calculator. There is also a printable roof pitch chart that fits on one page.

Common questions

What is an 11/12 roof pitch in degrees?

42.51 degrees, which is a 91.7 percent slope.

What is the pitch multiplier for an 11/12 roof?

1.357. Multiply a level run or a flat area by it to get the sloped length or the roof area.

How long is a rafter on a 24 foot wide building at 11/12?

About 16' 3 3/8" from the ridge to the outside of the wall, before any overhang or ridge board deduction. The ridge sits 11' 0" above the top of the wall.

Can you put asphalt shingles on an 11/12 roof?

Yes. An 11/12 roof is above the 4 in 12 mark, so asphalt shingles go on with standard single underlayment.

Is an 11/12 roof walkable?

An 11/12 roof is too steep to walk on. Work at this pitch calls for roof jacks, staging and a harness. Any roof is dangerous when wet.

Is an 11/12 roof the same as 45 degrees?

No. A 45 degree roof is 12/12. An 11/12 roof is 42.51 degrees.

How much more roof does 11/12 have than 6/12?

About 21 percent more over the same house. The pitch multipliers are 1.357 and 1.118.

Tools for this job

Each link opens an Amazon search for that item. As an Amazon Associate I earn from qualifying purchases.

Sources

Facts on this page were last checked against these sources in October 2026.

Related calculators